RedNet A16R MkII

16x16 Analogue I/O With Independent Level Control

RedNet A16R MkII is a 16-channel analogue interface for Dante® networks, with two channels of AES3 I/O. Precision A-D and D-A conversion provides 119dB of dynamic range, flat from 20Hz - 20kHz (+/- 0.15dB). Individual input and output channel level controls allow for precise adjustment of all I/O levels using RedNet Control. With two power supplies and primary and secondary EtherCON network connectors, RedNet A16R MkII is perfect for critical-path applications in recording, post production, live sound and broadcast. Built-in redundancy features allow for silent fail-over in the event of power or network outage, providing reassurance for system technicians.

Analogue inputs and outputs are connected through four rear-panel AES59 standard DB25 connectors, while an additional pair of AES3 I/O is provided through male and female XLR for added flexibility. The XLR input can accept DARS signals in addition to AES3. Word Clock I/O on BNC connectors allows external devices to clock to RedNet A16R MkII, or alternatively allows RedNet A16R MkII to act as a network clock grand master, following an external input.

RedNet A16R MkII is well suited to both permanent installation and repeated strike and setup: all connectors lock and remain terminated even under stress, providing worry-free installation and peace of mind once situated in a rack. In addition, all Focusrite Pro products come with a three-year warranty and award-winning customer support.

Key Features

• 16-channel bi-directional analogue interface for Dante networks, with additional two-channel AES3 I/O.
• Precision A-D and D-A conversion with 119dB dynamic range, flat from 20Hz - 20 kHz (+/- 0.15dB).
• Individual input/output channel level control using RedNet Control software.
• Dual PSUs with locking IEC inlets.
• Dual locking etherCON connectors for Primary and Secondary network connections.
• Power supply and ethernet redundancy with auto switchover in case of failure.
• Front-panel LED indicators for PSU, network, sample rate, signal present and clock source status.
• Sample rate conversion on the AES3 inputs allows external equipment to run at any sample rate.
• Analogue I/O on four AES59 standard DB25 connectors.
• Digital I/O on a pair of XLR connectors (AES3).
• Rear panel XLR connector can either be used as a DARS input or as a traditional AES3 audio input.
• BNC connectors for Word Clock input and output.
• Compact 1U chassis allows maximum functionality in minimum rack space.
• AES67 and AES70 compliant.
• SMPTE ST 2110 compliant when used with Dante Domain Manager (sold separately).
• Full operability with Focusrite RedNet and Red interfaces, plus all Dante devices from hundreds of manufacturers.
• Remote control with RedNet Control, and route via Dante Control.

16x16 AES3 I/O with independent level control

The RedNet D16R MkII is a 16-channel bi-directional AES3 interface for Dante® networks. The 1U rackmount device features individual input and output channel level controls, allowing for precise calibration and control of all input and output levels using RedNet Control. RedNet D16R MkII features power supply and Ethernet redundancy with auto switchover in case of failure.

Various connection options make RedNet D16R MkII a flexible addition to any Audio-over-IP system. A pair of DB25 multipin connectors each connect eight channels of AES3 I/O into and out of the interface, while XLR and RCA ports enable two-channel AES3 and S/PDIF connections, respectively, to be made.

Sample rate conversion on every input enables external equipment to operate at different sample rates, and DARS signals are accepted on the XLR connector. Word Clock I/O on BNC connectors allows synchronisation to house clock, or syncing external equipment to the Dante network.

The Focusrite Studio Console reborn in your DAW

The Focusrite Studio Console defined countless hits of the 80s and 90s, thanks in large part to its ISA 110 Equaliser and ISA 130 Dynamics Modules. Brainworx's bx_console Focusrite plug-in brings you stunningly accurate emulations of both in a single plug-in, perfectly capturing the famously warm, open sound of two of the most revered pieces of studio hardware ever made.

Specifications in detail

Line inputs

0 DBFS Reference Levels: +18 or 24dBu (switchable)

Frequency Response: 20Hz – 20kHz ± 0.1dB

THD+N: Less than -100dB (0.001) unweighted, 20Hz – 20kHz; -1dBFS input

EIN: -96dBu A-Weighted (typical)

Signal-To-Noise Ratio: 120dB A-Weighted (typical)

Converter Dynamic Range: 120dB A-Weighted (typical), 10Hz – 20kHz

Line outputs

0 DBFS Reference Levels Outputs: 18 or 24dBu (switchable)

Frequency Response Outputs: 20Hz – 20kHz ± 0.1dB

THD+N Outputs: Less than -100dB (0.001) unweighted, 20Hz – 20kHz; 23dBu input

Noise In Presence Of Signal: -94dBu A-Weighted (typical)

Dynamic Range: 118 dB A-Weighted (typical)

Converter Dynamic Range Output: 120dB A-Weighted (typical), 10Hz – 20kHz

Digital input sample rate converters

Sample Rate Range: 32kHz to 216kHz

Gain Error: -0.3dB

Dynamic Range Inputs: Greater than 138dB

THD+N Inputs: Less than -130dB (0.00003)

Latency: 11 to 45 samples (network and sample rate dependent)

Digital performance

Supported Sample Rates: 44.1 / 48 / 88.2 / 96 / 176.4 / 192 kHz (-4 / -0.1 / 0.1 / 4.167) at 24 bit

Clock Sources: Internal or from Dante Network Master

External Word Clock Range: Nominal sample rate ±7.5

Rear panel connectivity

Line Inputs: 2 x DB25 connectors

Line Outputs: 2 x DB25 connectors

Channel Count: 2 x 2 AES/EBU channels

Input (Optional DARS): 1 x Female XLR (Switchable with analogue input channels 15 and 16 at quad rates)

Output: 1 x Male XLR (Duplicate of analogue output channels 15 and 16 at quad rates)

Word Clock Input: 1 x BNC 75O port (switchable termination)

Word Clock Output: 1 x BNC 75O port

PSU: 2 x IEC Inputs with retaining clips

Network: 2 x EtherCON NE8FBH, also compatible with standard RJ45 connectors